.. |
alts-and-deprecated
|
added printable shaft coupler and some doc images
|
9 years ago |
belt-guide-624.stl
|
remaining stls, extruder files, and a bom
|
10 years ago |
coupler-5x8.stl
|
add power inlet detail photos
|
5 years ago |
extruder-clamp.stl
|
add power inlet detail photos
|
5 years ago |
extruder-direct-drive.stl
|
some reorganization of files
|
9 years ago |
extruder_idler.stl
|
add power inlet detail photos
|
5 years ago |
fanduct-e3dlite6.stl
|
adding fan duct
|
10 years ago |
filament-mount.stl
|
Wilson II initial commit
|
10 years ago |
filament_mount_left.stl
|
add power inlet detail photos
|
5 years ago |
pica-mount.stl
|
added printable shaft coupler and some doc images
|
9 years ago |
psu-mount-bottom.stl
|
new PSU mount with IEC receptacle
|
9 years ago |
psu-mount.stl
|
new PSU mount with IEC receptacle
|
9 years ago |
ramps-mount.stl
|
fixed missing slots on ramps mount
|
9 years ago |
smartlcd-mount.stl
|
Wilson II initial commit
|
10 years ago |
x-carriage.stl
|
some reorganization of files
|
9 years ago |
x-end-idler.stl
|
tightened up a few loose fittings and added pica board mount
|
9 years ago |
x-end-motor.stl
|
tightened up a few loose fittings and added pica board mount
|
9 years ago |
x-tensioner.stl
|
Revised X & Y tensioners for improved strength
|
8 years ago |
y-brace.stl
|
fixed a thickness error on the psu mount bracket, added beveled lower corners to y-brace, and rod clearance for y-table
|
9 years ago |
y-idler.stl
|
beefed up some parts for strength (y-idler, z motors) and tweaked y-table for belt offset
|
9 years ago |
y-motor.stl
|
tightened up a few loose fittings and added pica board mount
|
9 years ago |
y-table-10.stl
|
beefed up some parts for strength (y-idler, z motors) and tweaked y-table for belt offset
|
9 years ago |
y-tensioner.stl
|
Revised X & Y tensioners for improved strength
|
8 years ago |
z-lower-brace-1.stl
|
Y idler end rod holes shrunk by .4mm, lower z braces put through netfabb
|
9 years ago |
z-lower-brace-2.stl
|
Y idler end rod holes shrunk by .4mm, lower z braces put through netfabb
|
9 years ago |
z-lower-brace-pair.stl
|
beefed up lower z brackets, added holes to the LM2596 mount for alternate PCB, thickened X tensioner yoke
|
9 years ago |
z-motor-left.stl
|
add power inlet detail photos
|
5 years ago |
z-motor-right.stl
|
add power inlet detail photos
|
5 years ago |
z-pinion.stl
|
add power inlet detail photos
|
5 years ago |
z-rack.stl
|
add power inlet detail photos
|
5 years ago |
z-top-left.stl
|
add power inlet detail photos
|
5 years ago |
z-top-right.stl
|
add power inlet detail photos
|
5 years ago |